Forums HomeRegisterSearchFAQRulesUsergroupsLog in
Tt Invitational Competition Entry- Adrenal Express FINISHED!
Goto page 1, 2, 3  Next
PDXLAN Forum Index -> Modding Discussion » Project logs Only. All times are UTC - 8 hours Reply to topic
Author Message
Boddaker
2nd Lieutenant
2nd Lieutenant




Posts: 951

Location:
Where beer flws like wine

Tt Invitational Competition Entry- Adrenal Express FINISHED! Reply with quote
Greetings everyone! It's such an honor to be selected to represent the US in Thermaltake's CaseMod Invitational, Season 2!



This is going to be a really exciting competition, with so many talented modders battling it out. I can't wait to see what everyone comes up with, using the X9 chassis. [Smile]


Here are my requisite photos of all the great hardware that will be going into this build. Special thanks go to not only Thermaltake for hosting this amazing competition and providing for most of the hardware, but also to Avexir for the sweet DDR4 memory kit, and to Newegg!


Here is an overall shot of the booty, case and all..




Thermaltake ToughPower 1200w power supply



ASUS Sabertooth X99 motherboard



ASUS Strix GTX 970 video cards X2



Intel i7 5820K processor



Avexir DDR4 16Gb Memory Kits X2



Samsung 850 EVO 240Gb SSDs X3



Thermaltake hot swap dual drive bays X2



360mm Rads X3



200mm Res/Pump combos X2



Soft tubing



Rigid tubing



Miscellaneous fittings (too many to itemize lol)



STRIX 970 waterblocks X2



120mm Riing Fans Green X9



200mm Luna Fan white



Commander FT Fan Controller



Commander FX 10 port Fan Hub


_________________
Bods-Mods.com - Modding the world, one case at a time.


Last edited by Boddaker on Mon Nov 02, 2015 10:38 am; edited 3 times in total
Fri Sep 11, 2015 9:31 am
View user's profile Send private message   Visit poster's website Yahoo Messenger Post
Boddaker
2nd Lieutenant
2nd Lieutenant




Posts: 951

Location:
Where beer flws like wine

Reply with quote
I really like the X9, not only for it's size, but also for the shear number of options and configurations one can choose to go with when building a system. It literally takes the boredom out of putting a computer system together because it can be built in so many different ways within this one chassis. This is evidenced by the myriad of X9 rigs out there right now that people have built for themselves and others, each one vastly different than the next, much like snowflakes in their uniqueness.

That's why when I took delivery of my X9, I felt a sense of anticipation, as if I was stepping into the unknown, my path uncertain. I was giddy with excitement, eager to tear into the box like a child and his present on Christmas morning. My heart started racing and I quickly scribbled my illegible signature on the delivery man's tablet and waved him off, never once taking my eyes off the box. My new enemy became the very cardboard that had served to protect that which was concealed inside, and was quickly subdued as I targeted its weakest points with the first thing I could find within reach: my house key. Stabbing the packing tape repeatedly along its seams, I eventually succeeded in opening the box, only to find the X9 was yet unseen; obfuscated by Styrofoam and plastic (Dr. Cardboard's obvious cohorts). But even these final layers of protection were no match, and ultimately yielded to my unrelenting desire to gaze upon my new case.

After a few moments of silent staring and admiration, I took a deep breath as I began to contemplate my seemingly impossible task of deciding what to do for a theme. The choices are virtually unlimited! How can I settle on one single idea? Should I go with a video game theme, or movie? What could I do that hasn't already been done a hundred times over? Then the answer just appeared before me as I watched the delivery truck start up outside and drive off. This whole thing that I had just experienced, the anticipation, the excitement, the excelerated heartbeat... it was like getting a shot of adrenaline. Before the X9 arrived, I was bored, tired and lethargic. And once it got here, I felt awake, motivated, inspired.. I felt alive! So this theme will exemplify that feeling of heightened alertness. The Core X9 will become the vessel that transports this highly exuberant chemical to its new owners, curing them of the common doldrums. Of course, there is only one company internationally certified to carry such a fragile, and extremely rare commodity...

And that company is:




_________________
Bods-Mods.com - Modding the world, one case at a time.
Fri Sep 11, 2015 9:38 am
View user's profile Send private message   Visit poster's website Yahoo Messenger Post
Boddaker
2nd Lieutenant
2nd Lieutenant




Posts: 951

Location:
Where beer flws like wine

Reply with quote
Since Adrenaline is such a potent chemical, it must be handled very carefully. If just one drop should escape from its container, the consequences would be devastating. So first and foremost, construction of the transportation unit is critical, and extreme care in keeping the Adrenaline stable is paramount. That is why these heavy duty shock absorbers will be employed on every corner to ensure that no vibration makes its way into the container..




These heavy duty shock absorbers, normally used on full suspension mountain bikes, will be put to better use here.






Taking 1" square box tubing, I cut eight individual pieces out for mounting the shocks to the inner chamber.



The shock fits inside the bracket, utilizing the mounting hardware that came with it.



All eight chamber mounts done.



For the other end, a slightly different design was needed to mount the shock to the corners of the outer frame. More 1" box tubing was sectioned out.



Cut and drilled to accept the shock bolt.



All mounting brackets done!



These triangle pieces will fit into the corners of the frame.



The top brackets are drilled in the center, and the holes squared.



This keeps the carriage bolt from spinning when the nut is screwed on.



Both pieces fastened together.



A 1" flat washer is used to reinforce the bracket and spread out the load.


Once the frame is prepped, these brackets will then be riveted into place. More soon!


_________________
Bods-Mods.com - Modding the world, one case at a time.
Fri Sep 11, 2015 9:45 am
View user's profile Send private message   Visit poster's website Yahoo Messenger Post
DarthBeavis
Lt. Colonel
Lt. Colonel




Posts: 12385

Location:
salem, Oregon

Reply with quote
very neato

_________________
I quit FB and Twitter and will not be on the forums much so please email me if you have modding needs or whatever (my shop is still available for PDXLAN modders). Elmexijedi@gmail.com
Fri Sep 11, 2015 10:21 am
View user's profile Send private message   Post
Govtman
1st Lieutenant
1st Lieutenant




Posts: 1361

Location:
Salem Oregon

Reply with quote
DarthBeavis wrote:
very neato


^^^^
THIS - at the very least! Yay! Another Bod Mod!!!

_________________
Meddle not in the affaires of Dragons, for thou art crunchy and taste delicious with SALSA-Q. But then, doesn't everything????
Fri Sep 11, 2015 3:14 pm
View user's profile Send private message [ Hidden ] Post
ElmyPwns
1st Lieutenant
1st Lieutenant




Posts: 1060

Reply with quote
The Master at work again.... This is going to be good.

_________________
Main rig 5960X @ 4.5GHZ with MSI Godlike MB , Quad Fury X's , 512GB Samsung Pro M.2 NVMe. 2 Crucial MX200 512MB for storage. 64 GB Crucial Elite DDR4-2666.
Sat Sep 12, 2015 7:40 pm
View user's profile Send private message   Post
Boddaker
2nd Lieutenant
2nd Lieutenant




Posts: 951

Location:
Where beer flws like wine

Reply with quote


The inner chamber of the Adrenaline Transport Container was completed over the weekend, using only the highest grade galvanized steel sheet. The galvanization process alters the molecular structure of the steel, creating a superior adrenaline-proof barrier, should any leaks occur. Our courier's safety is of utmost importance here at Adrenaline Express!

Marking out the dimensions of the inner chamber onto raw galvanized stock.


A jigsaw outfitted with high tensile strength tungsten carbide blades was used to cut the specially treated steel.


After bending, we have four sides.


A separate piece for the back was made, with a 1/2" lip all around..


The back fits perfectly inside the four sides.


Once riveted together, I could start test-fitting parts inside the chamber. First was to ensure the two Adrenaline Reservoirs would fit snugly in their places.


Next will be placement of the main control board, which will be responsible for regulating the environmental conditions of the chamber, as well as monitoring vibrations.


_________________
Bods-Mods.com - Modding the world, one case at a time.
Mon Sep 14, 2015 1:53 pm
View user's profile Send private message   Visit poster's website Yahoo Messenger Post
Boddaker
2nd Lieutenant
2nd Lieutenant




Posts: 951

Location:
Where beer flws like wine

Reply with quote


Got all the shock absorbers mounted over the weekend!

Working on the top shocks first, I got the corner shock brackets mounted into the corners using the existing pop rivet holes.


For the top shock mounts, I had to cut the ends off of the radiator support bracket to make room in the corners.


The back two shocks mounted..


..and the front two..


All four top shocks mounted to the corners.


After measuring and centering the inner chamber at the correct height, I drilled holes on all four corners to mount the other shock brackets.


Flipping the entire case over, I started working on the bottom shocks.


I removed the inner chamber temporarily so I could have room to work, and proceeded to mount the remaining four shocks in the bottom corners.


While the chamber was out, I drilled holes in the bottom using the same measurements as the top, and re-installed it into the case.


We now have a fully suspended inner chamber!








_________________
Bods-Mods.com - Modding the world, one case at a time.
Mon Sep 21, 2015 11:53 am
View user's profile Send private message   Visit poster's website Yahoo Messenger Post
DarthBeavis
Lt. Colonel
Lt. Colonel




Posts: 12385

Location:
salem, Oregon

Reply with quote
When this mod is a rocking, don't come a knocking.

_________________
I quit FB and Twitter and will not be on the forums much so please email me if you have modding needs or whatever (my shop is still available for PDXLAN modders). Elmexijedi@gmail.com
Mon Sep 21, 2015 2:17 pm
View user's profile Send private message   Post
Vaelin
Lt. Colonel (Mod)
Lt. Colonel (Mod)




Posts: 948

Location:
Tigard, OR

Reply with quote
That is going to be so cool.

If you need anything CNC cut...... Wink

_________________
PDXLan 1,2,3,4,5,6,7,8,9,10,10.5,11,12,12.5,13,14,14.5,15,16,16.5,17,18,18.5,19,20,20.5,21,22,22.5,23,24,24.5,25,26,26,26.5,27,28,28.5,29,30,30.5,31,32A,32B - Ad Infinitum & Vectorlan 1,2,3,4,5,6,7,8,9
minecraft: nlancaster
PDXLan.com: Vaelin
Origin/UPlay: Vaelin_the_One
Mon Sep 21, 2015 5:23 pm
View user's profile Send private message   Visit poster's website Post
DarthBeavis
Lt. Colonel
Lt. Colonel




Posts: 12385

Location:
salem, Oregon

Reply with quote
Vaelin wrote:
That is going to be so cool.

If you need anything CNC cut...... Wink


Bod is so famous, CNC shops pay him to let them cut parts for his projects

_________________
I quit FB and Twitter and will not be on the forums much so please email me if you have modding needs or whatever (my shop is still available for PDXLAN modders). Elmexijedi@gmail.com
Mon Sep 21, 2015 5:39 pm
View user's profile Send private message   Post
Vaelin
Lt. Colonel (Mod)
Lt. Colonel (Mod)




Posts: 948

Location:
Tigard, OR

Reply with quote
In Boddakers world the metal cuts itself.

_________________
PDXLan 1,2,3,4,5,6,7,8,9,10,10.5,11,12,12.5,13,14,14.5,15,16,16.5,17,18,18.5,19,20,20.5,21,22,22.5,23,24,24.5,25,26,26,26.5,27,28,28.5,29,30,30.5,31,32A,32B - Ad Infinitum & Vectorlan 1,2,3,4,5,6,7,8,9
minecraft: nlancaster
PDXLan.com: Vaelin
Origin/UPlay: Vaelin_the_One
Mon Sep 21, 2015 6:18 pm
View user's profile Send private message   Visit poster's website Post
DarthBeavis
Lt. Colonel
Lt. Colonel




Posts: 12385

Location:
salem, Oregon

Reply with quote
Vaelin wrote:
In Boddakers world the metal cuts itself.



Bod is the Moses of modding, waives his staff and sea of aluminum parts

_________________
I quit FB and Twitter and will not be on the forums much so please email me if you have modding needs or whatever (my shop is still available for PDXLAN modders). Elmexijedi@gmail.com
Mon Sep 21, 2015 8:13 pm
View user's profile Send private message   Post
DarthBeavis
Lt. Colonel
Lt. Colonel




Posts: 12385

Location:
salem, Oregon

Reply with quote
into parts

_________________
I quit FB and Twitter and will not be on the forums much so please email me if you have modding needs or whatever (my shop is still available for PDXLAN modders). Elmexijedi@gmail.com
Mon Sep 21, 2015 8:14 pm
View user's profile Send private message   Post
Boddaker
2nd Lieutenant
2nd Lieutenant




Posts: 951

Location:
Where beer flws like wine

Reply with quote
rofl what am I, the Chuck Norris of modding now? Laughing

_________________
Bods-Mods.com - Modding the world, one case at a time.
Tue Sep 22, 2015 9:49 am
View user's profile Send private message   Visit poster's website Yahoo Messenger Post
Boddaker
2nd Lieutenant
2nd Lieutenant




Posts: 951

Location:
Where beer flws like wine

Reply with quote

The time has come to create the opening for the motherboard's IO, but I needed the factory cutouts for a template. I couldn't just put the entire case up next to the inner chamber, so I cut it out. Razz


Now I'm free to mark the openings with the stock "Ttemplate".. I included the GPU's IO brackets as well so I could transfer those holes for the displayport, HDMI, and DVI ports.


Holes marked..


Motherboard IO cut and the panel in for a test fit..


With that in place I knew right where to add the standoffs, so now the motherboard is mounted.


Moving on to the GPU cutouts..


Graphics cards installed!


Next up is drilling holes for the pump wires, along with other cables such as USB3 and front IO.



_________________
Bods-Mods.com - Modding the world, one case at a time.
Thu Sep 24, 2015 1:31 pm
View user's profile Send private message   Visit poster's website Yahoo Messenger Post
Boddaker
2nd Lieutenant
2nd Lieutenant




Posts: 951

Location:
Where beer flws like wine

Reply with quote


The power supply will be located on the back of the inner chamber, in between the two reservoirs. But in order to mount it there, I'll need to fabricate a bracket for it to sit on. So more galvanized steel was cut..


..and bent into a shelf-like form..


..Here's a couple shelfies..




The mounting holes were transferred to the bottom panel from the psu itself.



Using special diamond-carbide cutting wheels, I was able to remove the center of the panel for adequate PSU ventilation.


And the PSU mounted to the shelf.


Using a box, I propped up the PSU and shelf to the desired height so I could mark the holes on the inner chamber. It will be held in place by some pop rivets once everything is prepped and painted and ready for final assembly.




_________________
Bods-Mods.com - Modding the world, one case at a time.
Tue Sep 29, 2015 11:29 am
View user's profile Send private message   Visit poster's website Yahoo Messenger Post
clamdip
Lite Brite
1st Lieutenant
1st Lieutenant




Posts: 1732

Location:
pdx

Reply with quote
oh come on, you can try harder than that Razz
Tue Sep 29, 2015 2:14 pm
View user's profile Send private message   Yahoo Messenger XFire Address Post
Boddaker
2nd Lieutenant
2nd Lieutenant




Posts: 951

Location:
Where beer flws like wine

Reply with quote


This vessel will be carrying the potent adrenaline, so it needs to be very strong and impervious to cracking, crazing, scratches, bullets, lasers, sharks, ... and even laser sharks. And since there is nothing tangible on this earth presently that comes close to this, I had to travel into the future and bring back some transparent unobtanium. Fortunately, I found that the future Pringles chip containers were made of it and happened to be the exact sized cylinders I needed, and was able to purchase a couple cans from the local Eleventy-Seven (formerly known as 7-11).

Here's the stock container, ready to be upgraded.


The de-agitator was disassembled, and it's feeble exo-coating removed.


A special protective UltraViolet-activated barrier strip was applied to the outside.


To further dissipate all those UltraViolets, this semi-permeable alloy was added over top the barrier strips.




Once, reassembled, the housing's performance is greatly enhanced by these super cool racing stripes..


Both vessels have been upgraded, and ready to be filled with the toxic fluid.




_________________
Bods-Mods.com - Modding the world, one case at a time.
Thu Oct 01, 2015 11:39 am
View user's profile Send private message   Visit poster's website Yahoo Messenger Post
Cbissett
Warrant Officer
Warrant Officer




Posts: 404

Location:
Portland, Oregon

Reply with quote
those turned out really nice, great work!

_________________
Steam: Biss
Origin: BiSsz
Battle.net: Biss #11594
WoW: Justic (Paladin) -Burning Legion / Biss (Shaman) -Korgath
Thu Oct 01, 2015 2:34 pm
View user's profile Send private message [ Hidden ] Post
Display posts from previous:    
PDXLAN Forum Index -> Modding Discussion » Project logs Only. View next topic
View previous topic
Reply to topic
Page 1 of 3
Goto page 1, 2, 3  Next

 
Jump to: 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group
Design by Spork and Offbeat Hosting
© 2009 PDXLAN